COMPLETE TRAINING SYSTEM FOR SINGLE PHASE  AC MACHINES.
COMPLETE TRAINING SYSTEM FOR SINGLE PHASE  AC MACHINES with training and installation
Each system must be composed minimally by the following components:
    Universal Motor with protection
For operation with 220 V AC or DC .Ratings for connection to AC.
- Power: 0.2 kW
- Voltage: 230 V   AC case
Voltage: 140 V     DC case
- Current: 2.5 A  AC case
- Current: 3 A    DC case
- Frequency: 50 Hz
    Capacitor Motor
Single-phase AC motor with starting relay,
Capacitor Starting and run
Ratings:
- Power: 0.37 kW
- Voltage: 230 V
- Current: 2.6 A
- Frequency: 50 Hz
- Design: 4 pole
- Speed: 1400 min-1
    Capacitor Motor
Single-phase AC motor with centrifugal switch,Capacitor Starting and run
Ratings:
- Power: 0.25 kW
- Voltage: 230 V
- Current: 2.2 A
- Frequency: 50 Hz
- Power factor: 0.85
- Design: 4 pole
- Speed: 1420 min-¹
Motor Protection Switch 1-1.6A
Three-pole, with overload and instantaneous short-circuit trip, single-phasing sensitivity according to.
- Bimetal tripping, setting range: 1.0 - 1.6 A
Motor Protection Switch 1.6-2.4A
Three-pole, with overload and instantaneous short-circuit trip, single-phasing sensitivity according to
- Bimetal tripping, setting range: 1.6 - 2.4 A
On/Off Switch Three-Pole
Power Circuit Breaker Module
3-phase ON/OFF switch with auxiliary contact (NC) for transmission line model 380 kV.
 Can be controlled manually using ON/OFF pushbutton or externally via switching contact, TTL level or 24 V DC.
The switching state is indicated by LED's and is additionally available as TTL level from 4-mm sockets. Control input (switching contact, TTL level, 24 V DC) for external switch-off command (tripping on faults).
- Contact load capacity: 400 V AC, 3 A
- Mains connection: 115/230 V, 50 Hz with mains connecting cable and earthing-pin plug
    Machine Test System
Equipment set for recording the characteristicsof electrical machines.
    Software for recording the characteristics of Electrical Machines
    Multimeter
Features:
- Automatic socket blocking to prevent plugging of leads into the wrong sockets
- Automatic and manual battery cut-out
- Warnings for fuse breaks and overloads
- Automatic and manual range selection
- True effective value measurement: TRMS
- DC voltage ranges: 100 mV ... 1000 V
- AC voltage ranges: 100 mV ... 1000 V
- DC current ranges 1 A ... 10 A
- AC current ranges: 1 A ... 10 A
- Resistance measuring ranges: 100 Ω... 40 MΩ
- Frequency: 100 Hz .... 30 kHz
- Temperature: - 250 °C ... +1372 °C
- Resolution: 10 µV; 100 µA; 10 mΩ; 0.01 Hz; 0.1 °C
- Continuity/diode test: yes
- TRMS: AC and AC+DC, 10 kHz
- Fundamental error, V DC: 0.05 % of measured value / ± 3 digits

    Power factor meter
    Adjustable transformer 0...260 V, 4 A
    Moving Iron Meter 2.5 A
- Measurement ranges: 0 - 2.5 A
    Moving Iron Meter 100/400 V
    Set of 10 32 A safety bridging plugs, black
    Safety Bridging Plugs with Tap, black, set of 10
    Safety bridging plugs, yellow/green, set of 10
    Safety connecting leads, 32 A, it contain:-
•    2 each safety connecting lead, red 100 cm
•    2 each safety connecting lead, blue 100 cm
•    2 each safety connecting lead, red 50 cm
•    2 each safety connecting lead, blue 50 cm
•    2 each safety connecting lead, red 25 cm
•    2 each safety connecting lead, blue 25 cm
•    4 each safety connecting lead, black 100 cm
•    6 each safety connecting lead, black 50 cm
•    6 each safety connecting lead, black 25 cm
•    4 each safety connecting lead, black 10 cm
    Safety connecting lead 32 A, yellow/green, set of 10
    Mobile cable holder
    Mobile Experiment Stand,
    manual of 1P AC Machines (in English)
Required Software to manage experimental manuals and interface